Sort By
$
sample42

BESANTEK BST-CBF01 Circuit Breaker Identifier

Special
$
sample42

BESANTEK BST-CBF02 Circuit Breaker Finder With GFCI

$
sample42

Extech 40130: Non-contact AC Voltage Detector

$
sample42

Extech 40180: Tone Generator and Amplifier Probe Circuit Finder Kit

$
sample42

Extech CB10: AC Circuit Breaker Finder/Receptacle Tester

$
sample42

Extech CB20: Circuit Breaker Finder/Receptacle Tester

$
sample42

Extech CT20: Remote & Local Continuity Tester

$
sample42

Extech RT30: Wireless AC Circuit Identifier (914MHz) with External Probe

$
sample42

Extech SD900: 3-Channel DC Current Datalogger

$

BESANTEK BST-CBF01 Circuit Breaker Identifier

BESANTEK Circuit Breaker Identifier comprises of The Receiver and the Transmitter. The transmitter (Tx) draws a current from the mains supply circuit to which it is connected to. The signal current from the Tx is at about 10kHz. This current is then searched by the receiver to detect the Fuse, circuit breaker or the faulty circuit. The receiver is a tuned circuit which has its centre frequency tuned to about 10kHz. The sensor is located at the tip of the receiver. The amplitude of the receiver of the received signal is shown on a bar graph type LED's. The more LED's are ON, the stronger the signal.




   


Special
$

BESANTEK BST-CBF02 Circuit Breaker Finder With GFCI

BESANTEK Circuit Breaker Finder with GFCI, it automatically indicates the right breaker and with the help of the GFCI tester, the wiring can also be verified if it’s correctly wired or if it isn’t, it will indicate which of the 5 fault condition exists in the system. Suitable for house, office, factory power network reconstruction, etc.




   

$

Extech 40130: Non-contact AC Voltage Detector

Non-contact detection of AC Voltage

40130 is capable of detecting the presence of live wires before testing, this pocket-size AC voltage detector features a low-profile tip that can be inserted into outlet receptacles or used to trace along wire insulation to locate breaks. This detector measures from 100 to 600 VAC (50/60 Hz) with visual (flashing red LED) alarms and audible (beeping) tones that can be switched off. Use for line out testing, locating breaks and control panel troubleshooting. CE approved and UL Listed. Complete with convenient size with pocket clip, and two AAA batteries.

$

Extech 40180: Tone Generator and Amplifier Probe Circuit Finder Kit

Heavy duty kit with audible tone easily identifies wires or cables

The 40180 is a Tone Generator and Amplifier Probe Kit. This heavy-duty kit with audible tone easily identifies wires or cables. The insulated inductive probe tip prevents shorting conductors. Featuring a wire trace, continuity test, clear/busy/ringing line test, and tip/ring identification. Includes Alligator clips, RJ45 and RJ11 modular connectors, 9V battery and Case.

$

Extech CB10: AC Circuit Breaker Finder/Receptacle Tester

Locates circuit breakers and tests receptacle wiring

The CB10 is an AC Circuit Breaker Finder/Receptacle Tester that locates circuit breakers and tests receptacle wiring. The CB10 allows the user to quickly locate 110 Volt to 125-Volt AC circuit breakers and fuses with audible and visual circuit breaker indication. The product also features a variable sensitivity adjustment to pinpoint correct circuit breaker. This product is complete with a year warranty, the receiver and GFCI transmitter and a 9V battery for the receiver.

$

Extech CB20: Circuit Breaker Finder/Receptacle Tester

Quickly Locate Circuit Breakers, Confirm Proper Wiring and Test GFCI Circuits

Locate the correct circuit breaker or fuse without turning off the power with the Extech CB20 Circuit Breaker Finder, which employs automatic sensitivity to quickly and accurately pinpoint the correct 90-Volt to 120 VAC circuit breaker or fuse. The CB20 is ideal for a range of applications, including locating branch circuit breakers without causing accidental power shutoffs, confirming proper wiring during electrical installation or repair, and testing receptacle ground fault operation. Complete with Receiver, Transmitter, and 9V battery.

$

Extech CT20: Remote & Local Continuity Tester

One person operation for wire and cable testing

The CT20 is an electronic tool for electricians, alarm, cable installers and others who routinely need to check circuits for continuity and also identify cables and wires. It allows a single user to quickly identify and label two wires even when the wire ends are located in different rooms. It can accommodate test wire lengths up to 10,000-feet (3,000 meters), 26-gauge minimum. The CT20’s Remote Continuity mode allows the user to check continuity and to identify two or more cables/wires simultaneously.

$

Extech RT30: Wireless AC Circuit Identifier (914MHz) with External Probe

Local & Remote non-contact Voltage Detection + Remote Light Detection

The versatile RT30 uses a pager-sized, non-contact voltage detector transmitter which clamps onto wiring mid-run and transmits a "voltage present" signal to a pocket-sized receiver carried by the user. Clamped onto a live wire, the transmitter signals the user at the breaker panel with LED and audible alerts on the receiver (up to 100 m range). The alerts stop when the correct circuit breaker is switched and work can then be performed safely. You get the RT30 Wireless Remote AC Circuit Identifier with transmitter and receiver, remote clamp-style probe, 4 AAA batteries, pouch case, and operating instructions.

NOTE: USA, Mexico, and Canada use 914MHz model and majority of other countries use 869MHz model

$

Extech SD900: 3-Channel DC Current Datalogger

Records data to SD card in Excel® format

Extech's SD900 allows technicians to easily monitor and record DC mA values from 3 external sensors, transducers, and other sources using one meter. It also stores the time and date of when readings are taken. The logger features a large triple LCD display and records data on an SD card in an Excel®-ready format for easy transfer to a PC for analysis, trending, and archiving. Complete with six AAA batteries, SD memory card, Univeral AC Adaptor with multi-plugs (US, EU, UK, AUS), 3 input connect sockets, and mounting bracket.